A New Design and Optimization of a Three-Axis MEMS Capacitive Accelerometer with High Dy-namic Range and Sensitivity

Bahram Azizollah Ganji, Kamran Delfan Hemmati

Abstract


In this paper a three-axis capacitor accelerator has been designed, analyzed and optimized using micro-electromechanical systems technology. The accelerometers are generally divided into three categories of single axis, two axes, and three axes in terms of their ability to measure acceleration. In the suggested structure, acceleration measurements are carried out on all three axes simultaneously using a mass and spring system, which makes it possible to achieve a high sensitivity at a low occupancy level without losing other accelerator factors. By taking difference in this structure, it is shown that each axis acceleration has a very low impact on the measured acceleration of the other two axes. If any external factor changes the value of a single capacitor, the original output of the capacitor does not change for detecting acceleration. In other words, the acceleration of any of these three axes, due to its designing features, does not influence the other two axes and the system performance cannot be disrupted by external factors. The other important characteristics of the accelerometers are dynamic range, operating frequency and sensitivity. This study covers a dynamic range up to 1000g and an operating frequency up to 20 kHz. The accelerometer sensitivity is 4fF/g in the z axis direction while it is 9fF/g in the x and y axes directions. In this paper, the simulation of the structure is performed using Intellisuite software. Moreover, a multi-objective genetic optimization algorithm has been used to determine the dimensions of the constituents of the spring and the weight.

Keywords


Accelerometer; Three Axis; MEMS; Dynamic Range; Operating Frequency

Full Text:

PDF

References


W. Yuan, H. Chang, W. Li, B. Ma, “Application of an Optimization Methodology for Multidisciplinary System Design of Micro gyroscopes,” Journal of Microsystem Technologies, pp. 315-323,2006, https://doi.org/10.1007/s00542-005-0054-2.

j. Marek, H. P. Trah, Y. Suzuki, & I. Yokomori, Sensors for Automotive Applications, vol. 4, Wiley Press, 2005.

J. J. Allen, Microelectromecanical System Design, 1st Edition, CRC press, 2005.

S.Beeby, G. Ensell, M. Kraft, & N. White, MEMS Mechanical Sensors, Artech House Press, (2004).

P. Ashok Kumar, R. G. K. S. Prakash, & Rao, K. Srinivasa, "Design and Simulation of Capacitive Type Comb-Drive Accelerometer to Detect Heart Beat Frequency", International Journal of Biosen Bioelectron,pp.90‒91,2017, https://doi.org/10.15406/ijbsbe.2017.02.00024.

G. Lammel, The Future of MEMS Sensors in our Connected World, 28th IEEE International Conference on Micro Electro Mechanical Systems (MEMS), pp. 61–64, 2015, https://doi.org/ 10.1109/MEMSYS.2015.7050886.

M. Kraft, Closed-loop Accelerometer Employing Oversampling Conversion, PhD Thesis, Coventry University, 1996.

M. S. Moghadam, H. Arefi, & K. Mafinezhad, "A New Design and Optimization of Capacitive MEMS Accelerometer", International Journal of Simulation: Systems, Science & Technology, pp. 23-32, 2014, https://doi.org/ 10.5013/IJSSST.a.14.01.04.

Y. Terzioglu, T. Kose, K. Azgin & T. Akin, "Simple Out-of-Plane Capacitive MEMS Accelerometer Utilizing Lateral and Vertical Electrodes for Differential Sensing", IEEE Sensors, pp. 1–4, 2015, https://doi.org/10.1109/ICSENS.2015.7370306.

H. Tavakoli, & E. A. Sani,"A New Method for Eliminating cross Axis Sensitivity in Two Axis Capacitive Micromachined Accelerometers", 21st Iranian Conference on Electrical Engineering (ICEE), pp. 595-598, 2013, https://doi.org/ 10.1109/IranianCEE.2013.6599678.

V. Benevicius, V. Ostasevicius, & R. Gaidys, "Identification of Capacitive MEMS Accelerometer Structure Parameters for Human Body Dynamics Measurements", Sensors Journal, pp. 11184-11195, 2013, https://doi.org/10.3390/s130911184.

S. Tez, U. Aykutlu, M. M. Torunbalci, & T. Akin, "A Bulk-Micromachined Three-Axis Capacitive MEMS Accelerometer on a Single Die", IEEE Journal of Microelectromechanical Systems, pp. 1264-1274, 2015, https://doi.org/ 10.1109/JMEMS.2015.2451079.

C. Acar, & A. Shkel, MEMS Vibratory Gyrosceps, Springer Publishing Company, 2008.

M.Bao, H. Yang, "Squeeze film air damping in MEMS", Journal of Sensors and Actuators, pp. 3-27, 2007, https://doi.org/ 10.1016/j.sna.2007.01.008.

H. G. Momen, H. Tavakoli, E. A. Sani, "A 3-Axis MEMS Capacitive Accelerometer Free of Cross Axis Sensitivity", 24th Iranian Conference on Electrical Engineering (ICEE), pp. 1491-1494, 2016, https://doi.org/10.1109/IranianCEE.2016.7585757.

X, Zhou, L. Che, S. Liang, Y. Lin, X. Li, Y.Wang, "Design and Fabrication of a MEMS Capacitive Accelerometer with Fully Symmetrical Double-Sided H-Shaped Beam Structure", Journal of Microelectronic Engineering, pp. 51-57, 2015, https://doi.org/10.1016/j.mee.2014.10.005.

K. Delfan Hemmati, M. Behzad Fallahpour, A. Golmakani, K. Delfan Hemmati, "A High-Speed Hybrid Full Adder with Low Power Consumption", IEICE Electronics Express, 1900-1905, 2012, https://doi.org/10.1587/elex.9.1900.

H. Hamaguchi, K. Sugano, T. Tsuchiya, O. Tabata, "A Differential Capacitive Three Axis Soi Accelerometer Using Vertical Comb Electrodes", IEEE International Solid-State Sensors, Actuators and Microsystems Conference, pp. 1483-1486, 2007, https://doi.org/ 10.1109/SENSOR.2007.4300425.

B. Bais, B. Y. Majlis, "Structure Design and Fabrication of an Area changed Bulk Micromachined Capacitive Accelerometer, IEEE International Conference on Semiconductor Electronics, pp. 29-34, 2006, https://doi.org/ 10.1109/SMELEC.2006.381014.

J. Chae, H. Kulah, Najafi, K. "A Monolithic Three-Axis Micro-g Micromachined Silicon Capacitive Accelerometer, Journal of Microelectromechanic Systems", pp. 235-241, 2005, https://doi.org/10.1109/JMEMS.2004.839347.

I. Zeimpekis, M. Kraft, "Single Stage Deflection Amplification Mechanism in a SOG Capacitive Accelerometer", Journal of Procedia Chemistry, pp. 883-886, 2009, https://doi.org/org/10.1016/j.proche.2009.07.220.

K. H. L. Chau, S. R. Lewis, y. Zhao, R. T. Howe, S. F. Bart, R. G. Marcheselli, "An Integrated Force-Balanced Capacitive Accelerometer for Low-g Applications", Proceedings of the International Solid-State Sensors and Actuators Conference, pp. 472-476, 1996, https://doi.org/ 10.1109/SENSOR.1995.717294.

T. Tsuchiya, H. Funabashi, "A Z-Axis Differential Capacitive SOI Accelerometer with Vertical Comb Electrodes", 17th IEEE International Conference on Micro Electro Mechanical Systems, pp. 378–383, 2004, https://doi.org/ 10.1109/MEMS.2004.1290637.

P. Bruschi, A. Nannini, D. Paci, F. Pieri, "A Method for Cross-Sensitivity and Pull-In Voltage Measurement of MEMS Two-Axis Accelerometers", Sensors and Actuators A: Physical, Elsevier, pp. 185–193, 2005, https://doi.org/10.1016/j.sna.2005.04.028.




DOI: https://doi.org/10.33180/InfMIDEM2020.106

Refbacks

  • There are currently no refbacks.


Copyright (c) 2015 Bahram Azizollah Ganji, Kamran Delfan Hemmati

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.